Header image
are fuel possibilities
line decor
  
line decor

 
 
 
   


 

 
 
Working with LEDs and Project Specifications:

LEDs have different requirements when compared to incandescent bulbs, they need DC (direct current) and are polarity sensitive. The power in your home is typically AC (alternating current) and runs most appliances in your house, but the computer in front of you, your cell phone, stereo, and many other electronic devices typically use DC. To go from 120 volt AC to your DC device, the voltage is usually first reduced with a magnetic device (called a transformer) to a lower AC voltage, which varies depending on lighting need. You then take your AC and rectify it. A rectifier is a device that functions as a one-way check valve for electrons; they can only travel one way, emitting only positive voltage. The check valve is a diode, a semiconductor device that is related to our friend the LED, and the positive voltage emitted is DC. This operation of a rectifier is in the simplest of terms; there are a number of different designs. In addition to rectifying AC, they usually filter the voltage and possibly regulate it.

LEDs are polarity sensitive, which means that they need a positive voltage at the anode and negative or ground at the cathode. When an LED is connected correctly with the appropriate supply voltage (one to four volts, depending on type) it will illuminate. With polarity reversed, no light will illuminate. LEDs have a voltage limit in the correct and reversed polarity, this limit is specified by manufacturer. When connecting an LED you must consider its operating voltage and current.


To have a better understanding of LED voltage and current supply, you must understand Ohm's Law (some will be able to skip this step, and others should read closely). Amps are a measure of current, a measure of the amount of electricity flowing in a circuit. Volts are a measure of the amount of electrical potential. Ohms are a measure of resistance to current flow. Watts are a measure of power, you may know this as the measurement your utility company uses to charge you. To get volts when you know watts and amps or any two out of the four, here are some formulas:

V=I*R
R=V/I
I=V/R
P=I*V
V=Volts I=Amps R=Ohms P=Watts


Let's say I have a bright white LED with an operating voltage of 3-3.4 volts. For overall longevity, I am going to drive this LED at 3.2 volts at its rated current of 0.018 amps. I have an 8 volt regulated supply voltage, and I am going to have to add a resistor in series with the LED to get the correct voltage. Now I subtract the LED voltage from the supply voltage 8-3.2V= 4.8 volts. Now I divide that voltage by the LED current 4.8/.018 = 266.6 Ohms. I then choose the next highest standard resistor value of 270 Ohms. This resistor in effect drops the excess voltage across it, but there is a small power loss with the resistor and this has to be considered when aiming for efficiency.

Now if you're building a light, odds are that you're going to use more than one LED. To do this, you can wire them in series, parallel, or a combination of the two. Series is when you connect electrical components such as LEDs in a string, end to end, negative to positive to negative to positive, et cetera. When you connect LEDs in series each one drops X volts and adds up the total voltage, but the current needed remains the same. To connect LEDs in parallel, you connect each positive terminal together and each negative terminal together. The total voltage required remains the same, but the current required adds up.

When doing large LED strings with lower voltages, it may be necessary to wire the LEDs in a series-parallel configuration. An example of this would be a 12 volt lead acid battery with an actual voltage of 12.7 and a charging voltage of 13+. In this situation, we need to use a voltage regulator to ensure a safe voltage for the LEDs. Let's say the LED has an average voltage requirement of 3.3 volts, then we'll use a 10 volt voltage regulator and we'll wire series strings of 3 LEDs, dropping approximately 10 volts total. In addition, we can wire equal series strings in parallel with this string, keeping in mind that the polarity must junction at the correct point. With this arrangement, you can wire as many LED strings in parallel as you wish (or as the available current will allow). The design should also include the appropriately rated fuse, wired in series with the voltage regulator and the LED string set. This is a design I often use and favor because of its safety and flexibility for use in different off the grid homes.

If you are using AC line voltage, your safest bet is using a DC wall transformer (lovingly nicknamed “wall wart”). These come in both regulated and unregulated forms. Keep in mind that the unregulated version will have huge voltage swings depending on load, so adding a voltage regulator may be necessary for certain applications. You could, however, use the LEDs directly as an AC voltage rectifier, keeping in mind that the forward and reverse voltage limit will add up to more than the AC voltage. The number you should be working with is the peak value, which is the AC voltage multiplied by 1.414. You can wire two strings of LEDs in opposite polarity connections to your AC terminals for the appropriate calculated voltage. During the rising edge of the AC one string will light, during the falling edge, the other. This will happen at 60 cycles per second in most countries and should be hard to detect with the naked eye. This method however is very crude and basic, does not give the best LED life, and it is not very safe because you are dealing with AC line voltage and many terminal connections.

For my templates of the homemade LED light (construction viewable on YouTube), please click here to view as a PDF.

For comments, questions, or corrections, please email Casey@AllEnergies.net




 

 

spacer

 


 

Home | Our Blog | Biomass / Gasification
Hydro Power | Wind Power | Solar Power | LED Lighting
Economics | About Us | Contact Us